Flexible doctor blade-coated abiotic cathodes for implantable glucose/oxygen biofuel cells.

Implantable devices powered by batteries have been used for sixty years. In recent devices, lithium-based batteries are the most widely used power source. However, lithium batteries have many disadvantages in terms of safety, reliability, and longevity and require regular monitoring and substitution. Implantable glucose biofuel cells (BFCs) are increasingly seen as a potential future technology for replacing lithium-based batteries because they do not require surgical replacement after 8-10 years and have a theoretically unlimited lifetime thanks to the continued recovery of glucose and oxygen present in the human body. This paper shows the fabrication of flexible implantable abiotic cathodes, based on a nitrogen/iron-doped graphene catalyst, for glucose/oxygen biofuel cell application. An ink, based on nitrogen-iron doped graphene as the abiotic catalyst and chitosan as a binder, was prepared and coated on a flexible teflonated gas diffusion layer using doctor blade coating. The characterization of the biocathode shows an open potential circuit corresponding to the potential of the abiotic catalyst and a high oxygen reduction current density of up to 66 µA cm-2 under physiological conditions. Those cathodes remain stable for up to two years with a current density loss of only 25%. The flexible abiotic electrode cytotoxicity was evaluated by cell culture experiments showing living cells' high tolerance on the biocathode surface. This work demonstrates that this abiotic catalyst can be a promising alternative for the development of implantable glucose BFCs due to its stability and its cytocompatibility.

Valorization of Byproducts of Hemp Multipurpose Crop: Short Non-Aligned Bast Fibers as a Source of Nanocellulose.

Nanocellulose was extracted from short bast fibers, from hemp (Cannabis sativa L.) plants harvested at seed maturity, non-retted, and mechanically decorticated in a defibering apparatus, giving non-aligned fibers. A chemical pretreatment with NaOH and HCl allowed the removal of most of the non-cellulosic components of the fibers. No bleaching was performed. The chemically pretreated fibers were then refined in a beater and treated with a cellulase enzyme, followed by mechanical defibrillation in an ultrafine friction grinder. The fibers were characterized by microscopy, infrared spectroscopy, thermogravimetric analysis and X-ray diffraction after each step of the process to understand the evolution of their morphology and composition. The obtained nanocellulose suspension was composed of short nanofibrils with widths of 5-12 nm, stacks of nanofibrils with widths of 20-200 nm, and some larger fibers. The crystallinity index was found to increase from 74% for the raw fibers to 80% for the nanocellulose. The nanocellulose retained a yellowish color, indicating the presence of some residual lignin. The properties of the nanopaper prepared with the hemp nanocellulose were similar to those of nanopapers prepared with wood pulp-derived rod-like nanofibrils.

In situ mineralization of nano-hydroxyapatite on bifunctional cellulose nanofiber/polyvinyl alcohol/sodium alginate hydrogel using 3D printing.

This paper reports the manufacturing by 3D printing of scaffolds for in-situ mineralization of hydroxyapatite using aqueous suspensions of alginate and polyvinyl alcohol (PVA)-grafted cellulose nanofibers (CNF). Bifunctional CNF with carboxyl and aldehyde moieties were prepared from bleached bagasse pulp and crosslinked with PVA. Aqueous hydrogels for 3D printing were prepared by directly mixing PVA-grafted CNF with sodium alginate, with and without the addition of phosphate ions. A calcium chloride solution was sprayed during the printing process in order to partially crosslink alginate and to increase the dimensional stability of the printed gel. At the end of the printing process, the prepared scaffolds were dipped into a CaCl2 solution to: i) complete alginate crosslinking and ii) promote hydroxyapatite nucleation and growth by reaction with phosphate ions. In order to better understand the mechanisms governing manufacturing of scaffolds by 3D printing, the rheological behavior of alginate/PVA-grafted CNF and the mechanical properties of unit filaments obtained by direct hydrogel extrusion were investigated. The final scaffolds were characterized by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR) and thermogravimetric analysis (TGA). This study shows that 3D printed sodium alginate/PVA-grafted CNF hydrogels are promising scaffold materials for bone tissue engineering.

Use of Cellulose Nanofibers as an Electrode Binder for Lithium Ion Battery Screen Printing on a Paper Separator.

Water-based inks were formulated using cellulose nanofibers as a binder in order to directly front/reverse print lithium ion cells on a paper separator. Moreover, the high cohesion of electrodes as provided by cellulose nanofibers allowed for the embedding metallic current collectors in the electrodes during the printing stage, in order to develop a one-step printing and assembling process. Positive and negative inks based on LiFePO4, or graphite, respectively, and cellulose nanofibers, displayed rheological properties complying with a variety of printing processes, as well as with screen printing. Printed cells exhibited high electrical conductivity and adhesion between current collectors and inks, i.e., up to 64 ± 1 J/m². Electrochemical cycling tests at C/10 showed a reversible capacity during the first cycle of about 80 mAh/g, which slightly decayed upon cycling. Preliminary results and assembling strategies can be considered as promising, and they represent a quick solution for the manufacturing of lithium ion batteries. Work is in progress to improve these processing issues and the cycling performances of Li-ion cells.

Biomimetic Mineralization of Three-Dimensional Printed Alginate/TEMPO-Oxidized Cellulose Nanofibril Scaffolds for Bone Tissue Engineering.

The three-dimensional (3D) printed scaffolds were prepared by partial cross-linking of TEMPO-oxidized cellulose nanofibril/alginate hydrogel using calcium ions for printing the hydrogel while maintaining its shape, fidelity, and preventing the collapse of the filaments. The prepared scaffolds were fully cross-linked using calcium ions immediately after printing to provide the rigidity of the hydrogel and give it long-term stability. The composition of the prepared pastes was adjusted in view of the description of the hydrogel and 3D printing parameters. The rheological properties in terms of thixotropic behavior and viscosity recovery of hydrogels were investigated by performing steady shear rate experiments. The results show that the viscosity recovery for pure alginate hydrogel was only about 16% of the initial value, whereas it was 66% when adding cellulose nanofibrils to alginate. Consequently, the shape of the pure alginate scaffold was soft and easy to collapse contrarily to the composite scaffold. The biomimetic mineralization process of printed scaffolds using simulated body fluid, mimicking the inorganic composition of human blood plasma, was performed and the hydroxyapatite nucleation on the hydrogel was confirmed. The strength properties of the fabricated scaffolds in terms of compressive strength analysis were also investigated and discussed. The results show that the alginate/TEMPO-oxidized cellulose nanofibril system may be a promising 3D printing scaffold for bone tissue engineering.

Preparation of highly hydrophobic and lipophobic cellulose fibers by a straightforward gas-solid reaction.

This work describes a very simple, rapid, and efficient approach to the hydrophobization and lipophobization of cellulose fibers through their reaction with gaseous trichloromethylsilane (TCMS). The characterization of the modified surface involved FTIR-ATR and solid-state (29)Si NMR spectroscopy, scanning electron microscopy (SEM), and contact angle measurements with different liquids. The modification generated an inorganic coating around the fibers, associated with the construction of a three-dimensional network of Si-O-Si bridges partly bound to the polysaccharide macromolecules. This coating conferred both a high hydrophobicity and a lipophobicity to the samples even when the treatments applied modest TCMS quantities and reaction times as short as 30 s. The green connotation of this novel process constitutes an additional positive feature.

Adsorption of a cationic surfactant onto cellulosic fibers I. Surface charge effects.

The adsorption of four cationic surfactants with different alkyl chain lengths on cellulose substrates was investigated. Cellulose fibers were used as model substrates, and primary alcohol groups of cellulose glycosyl units were oxidized into carboxylic groups to obtain substrates with different surface charges. The amount of surfactant adsorbed on the fiber surface, the fiber zeta-potential, and the amount of surfactant counterions (Cl(-)) released into solution were measured as a function of the surfactant bulk concentration, its molecular structure, the substrate surface charge, and the ionic strength. The contribution of each of these parameters to the shape of the adsorption isotherms was used to verify if surfactant adsorption and self-assembly models usually used to describe the behavior of surfactant/oxide systems can be applied, and with which limitations, to describe cationic surfactant adsorption onto oppositely charged cellulose substrates.

Interactions between poly(ethylene oxide) and fatty acids sodium salts studied by surface tension measurements.

This work focuses onto the interactions between poly(ethylene oxide) (PEO) and fatty acids, in order to set their potential role of contaminants for PEO-based retention systems. Surface tension measurements were used to investigate PEO-fatty acid systems and they made it possible to clearly point out the interactions between the polymer and the sodium octadecylcarboxylates with different degrees of unsaturation. The observed interaction seems to be dependent on the fatty acids' solubility, the increase of which leads to less pronounced phenomena, which are, in contrast, emphasized by the increase in PEO chain length.

Surface rheology and foaming properties of sodium oleate and C12(EO)6 aqueous solutions.

The dynamic surface tension (DST) and the surface viscoelastic modulus of sodium oleate aqueous solutions at different concentrations were measured using an image analysis tensiometer based on the oscillating bubble technique. The diffusion coefficient of oleate moieties was calculated from DST measurements and the surface viscoelastic modulus using the Langmuir-Szyszkowski and the diffusion-controlled adsorption models. The viscoelastic moduli obtained from model calculations were compared with the corresponding experimental values. The diffusion coefficient of C(12)(EO)(6) in water and the parameters of the Langmuir-Szyszkowski adsorption isotherm were taken from the literature and used to calculate the surface viscoelastic modulus of its aqueous solutions at different concentrations. The foaming properties of both C(12)(EO)(6) and sodium oleate solutions, viz., the foam conductance and the water volume fraction in the foam, were measured using a commercial Foamscan device. Foaming experiments with C(12)(EO)(6) and sodium oleate solutions were carried out either under static conditions; i.e., the foam conductance and the water volume fraction were measured as a function of time after the generation of a fixed volume of foam, or under dynamic conditions; i.e., the foam conductance and the water volume fraction were measured during foam formation. The variations in the foam permeability as a function of surfactant concentration were related to the viscoelastic properties of the air/water interface and to the presence of micelles in the foam films. With foams in which the water volume fraction was higher than 0.05, the foam electrical conduction could be described using a simple parallel resistor model and their conductance measurements were related to the foam water volume fraction. The results related to water drainage under static conditions were used to interpret water drainage under dynamic conditions. Preliminary conjectures on the influence of foam permeability and water volume fraction on the yield of the flotation deinking process were drawn from these results.

Precipitation and Solubility of Calcium Soaps in Basic Aqueous Media.

Measurements of the surface tension of aqueous media containing calcium salts of different fatty acids, whose structure only varied by the number of C=C unsaturations along their aliphatic chains, showed that their solubility increased as a function of this parameter going from near zero for calcium stearate to 4x10(-4) mol l(-1) for the linolenate homologue. The solubility product of the calcium soap corresponding to each tested fatty acid was estimated by using the anionic fatty acids adsorption isotherms in order to obtain the amount of dissolved ionic fatty acid at increasing concentration of calcium ions. These findings are discussed in terms of their serious repercussions on the operations related to flotation deinking in waste paper recycling. Copyright 2001 Academic Press.